Keywords
simulator, electro pneumatic, dual design
Document Type
Article
Abstract
This study aims to: (1) determine the process of developing a learning media simulator for electro-pneumatic systems based on dual design, (2) knowing the effectiveness of learning media in the form of electro-pneumatic system simulators based on dual design. This research is a research and development adapted from the 4D development model, namely, Define, Design, Develop, and Disseminate. The subjects of this study were students of Mechanical Engineering Education in Semester IV and V, with 30 students taking pneumatic hydraulic courses. Data collection techniques in this study used questionnaires and interviews with research instruments in the form of interview guidelines and questionnaires. The data obtained were analyzed with a descriptive quantitative method. The results show that (1) the results of the development of learning media for electro-pneumatic system simulators based on Dual Design as supporting media for electro-pneumatic practices produce three main components, namely the working system in the pneumatic electro system, wiring diagrams, and electrical circuits, (2) the feasibility results of expert validation media is 84% (Very Good), expert material validation is 92% (Very Good), and user validation is 86% (Very Good). Therefore, the learning media for electro-pneumatic system simulator is feasible as a learning media in pneumatic hydraulic courses.
Page Range
307-317
Issue
3
Volume
9
Digital Object Identifier (DOI)
10.21831/jpv.v9i3.27345
Source
https://journal.uny.ac.id/index.php/jpv/article/view/27345
Recommended Citation
Ramdani, S. D., Pangestu, A., & Abizar, H. (2019). The dual-design-based pneumatic simulator as supporting media for electro-pneumatic practicum in vocational higher education. Jurnal Pendidikan Vokasi, 9(3), 307-317. https://doi.org/10.21831/jpv.v9i3.27345
References
Ahmadi, A. (2005). Strategi belajar mengajar. Pustaka Setia.
Ali, M. (1998). Strategi penelitian pendidikan. Angkasa.
Anderson, R. H. (1987). Pemilihan dan pengembangan media untuk pembelajaran. Rajawali.
Bahar, A. (2017). Redesign sistem pneumatik silinder unloading untuk pergantian arah feeding dengan installation direction vertical, horizontal, dan inclined. Jurnal Teknik Mesin, 5(2), 209-216.
Balau, A., Caruntu, C., & Lazar, C. (2011). Simulation and control of an electro-hydraulic actuated clutch. Mechanical Systems and Signal Processing, 25(6), 1911-1922. https://doi.org/10.1016/j.ymssp.2011.01.009
Clarke, L., & Winch, C. (2007). Vocational education: International approaches, developments and systems. Routledge.
Djohar, A. (2007). Pendidikan teknologi dan kejuruan. In Ilmu dan aplikasi pendidikan (pp. 1285-1300). Pedagogiana Press.
Fatkhurrokhman, M., Leksono, S. M., Ramdan, S. D., & Rahman, I. N. (2018). Learning strategies of productive lesson at vocational high school in Serang City. Jurnal Pendidikan Vokasi, 8(2), 163-172. https://doi.org/10.21831/jpv.v8i2.19485
Hudallah, N. (2010). Rancang bangun sistem pneumatis untuk pengembangan modul-modul gerak otomatis sebagai media pembelajaran. Jurnal Teknik Elektro, 2(1), 8-22. https://doi.org/10.15294/jte.v2i1.1583
Jamaludin, J., & Khairudin, M. (2017). Pengembangan trainer elektropneumatik pada kompetensi mengoperasikan sistem kendali elektropneumatik. Jurnal Pendidikan Teknik Elektro, 7(2), 108-116. http://journal.student.uny.ac.id/ojs/index.php/elektro/article/view/8662
Khoshnevis, B. (1994). Discrete system simulation. McGraw Hill.
Kurniawan, R. (2008). Rekayasa rancang bangun ssistem pemindahan material otomatis dengan sistem elektro pneumatik. Jurnal Energi Dan Manufaktur, 2(1), 42-47. https://ojs.unud.ac.id/index.php/jem/article/view/2263
Li, B., Gao, L., & Yang, G. (2013). Evaluation and compensation of steady gas flow force on the high-pressure electro-pneumatic servo valve direct-driven by voice coil motor. Energy Conversion and Management, 67, 92-102. https://doi.org/10.1016/j.enconman.2012.11.004
Najjari, B., Barakati, S. M., Mohammadi, A., Fotuhi, M. J., Farahat, S., & Bostanian, M. (2012). Modelling and controller design of electro-pneumatic actuator based on PWM. International Journal of Robotics and Automation (IJRA), 1(3), 125-136. https://doi.org/http://dx.doi.org/10.11591/ijra.v1i3.565
Najjari, B., Barakati, S. M., Mohammadi, A., Futohi, M. J., & Bostanian, M. (2014). Position control of an electro-pneumatic system based on PWM technique and FLC. ISA Transactions, 53(2), 647-657. https://doi.org/10.1016/j.isatra.2013.12.023
Oladapo, B. I., Balogun, V. A., Oyegoke, S., Adeoye, A. O. M., Ijagbemi, C. O., Afolabi, S. O., Daniyan, I. A., Akinola, S. O., Simeon, A. P., & Uchegbu, I. D. (2016). Experimental analytical design of CNC machine tool SCFC based on electro-pneumatic system simulation. Engineering Science and Technology, an International Journal, 19(4), 1958-1965. https://doi.org/10.1016/j.jestch.2016.08.010
Raharjo, R. (2013). Rancang bangun belt conveyor Trainner sebagai alat bantu pembelajaran. Jurnal Teknik Mesin, 4(2), 15-26.
Rubio, E. R., Hernandes, L., Aracil, S. R., Roque, S., & Guerra, J. A. (2009). Implementation of decoupled model-based controller in a 2-DOF pneumatic platform used in low-cost driving simulators. 2009 Electronics, Robotics and Automotive Mechanics Conference (CERMA), 338-343. https://doi.org/10.1109/CERMA.2009.22
Sadiman, A., Rahardjo, R., Haryono, A., & Rahardjito, C. (2010). Media pendidikan (Pengertian, pengembangan, dan pemanfaatannya). Raja Grafindo Persada.
Setiadi, A., Yuliatmojo, P., & Nurhidayat, D. (2018). Pengembangan aplikasi Android untuk pembelajaran pneumatik. Jurnal Pendidikan Vokasional Teknik Elektronika, I(1), 1-5.
Syaefrudin, N. (2016). Pengembangan media pembelajaran trainer kit sensor dan aktuator untuk meningkatkan hasil belajar. Jurnal Pendidikan Teknik Mekatronika, 6(3), 258-267.
Tafakur, T., & Solikin, M. (2018). Electronic spark advance ignition system simulator as instructional media for assisting electrical practices on automotive field. VANOS Journal of Mechanical Engineering Education, 3(1), 43-50. https://doi.org/10.30870/vanos.v3i1.3377
Taylor, G. R., & MacKenney, L. (2008). Improving human learning in the classroom theories and teaching practices. Rowman & Littlefield Education.
Wiyanto, T., Samani, M., & Sugiyono, S. (2017). The developing teaching practice model as an effort to improve the quality of mechanical engineering vocational school teachers. Jurnal Pendidikan Vokasi, 7(3), 349-363. https://doi.org/https://doi.org/10.21831/jpv.v7i3.17923
